How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
We've uncovered this article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and felt it made good sense to discuss it with you on my blog.
Installing a tub isn't precisely rocket science, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably difficult project. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as place the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your washroom if you have already bought a brand-new bathtub and don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite troublesome due to the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub must wait till the bath tub has actually been utilized a minimum of once as this will certainly resolve it right into its final position.
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are sold in tubes as well as cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that write-up about How to Install a Bathtub through an acquaintance on another web blog. Are you aware of somebody else who is interested by the topic? Take a moment to share it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Set An Appointment
Report this page